A pool that needs topping up more often than usual can turn a relaxing garden feature into a costly worry. The best way to find pool leaks is to first separate normal evaporation from genuine water loss, then use targeted testing to identify whether the problem is in the pool shell, fittings or hidden pipework. Acting early matters, particularly during warm, dry weather in Spain, when a small leak can be easy to dismiss.
A hidden pool leak does not always create a dramatic puddle. It may show up as a rising water bill, damp ground around the pool, loose tiles, a drop in water level when the pump runs, or a pool that needs constant chemical top-ups. Finding the exact source before arranging repairs protects the pool, surrounding terrace and garden from unnecessary disruption.
Start by ruling out evaporation
Evaporation is a normal part of owning a pool, especially in hot weather, with wind, direct sun and heated water all increasing the rate. Splashing, backwashing and water carried out on swimmers can also make the level fall. However, evaporation should be gradual and broadly consistent.
The simplest initial check is the bucket test. Fill a bucket with pool water and place it on a pool step so that the water inside the bucket is at the same level as the pool water outside it. Mark both levels, then leave it for 24 hours with the circulation system switched off. Keep children and pets away from the area while the test is underway.
If the water level in the pool drops noticeably more than the water in the bucket, the pool is likely leaking. Repeat the same test with the pump running. A larger loss when the system is operating points towards a fault in the circulation pipework, pump, filter, valves or fittings. Similar water loss in both tests may suggest a leak in the pool structure or a fitting below the normal waterline.
This test cannot pinpoint the leak, but it gives useful evidence and prevents unnecessary guesswork.
Check the visible areas before making repairs
Once a leak is suspected, inspect accessible areas carefully. Look around the skimmer, return jets, lights, ladder anchors, vacuum points and pool steps. These are common places for seals, fittings and surrounding finishes to fail over time.
Pay attention to small details: cracks in grout or coping, missing sealant, staining on the waterline, air bubbles returning to the pool, or damp patches beside equipment. If the pool has a liner, look for wrinkles, tears or areas where the liner has pulled away from a fitting. In a tiled or concrete pool, loose tiles and hollow-sounding sections can indicate water has travelled behind the surface.
Do not assume the point where you can see water is the source. Water naturally follows the easiest route through soil, concrete and gaps in construction. A wet area several metres from the pool may be caused by a leaking underground pipe, not a crack directly beneath it.
Use the water level to narrow down the area
Allowing the water level to fall naturally can sometimes provide another clue. If it stops dropping at the level of a particular fitting, such as a skimmer mouth, return jet or light, that fitting deserves closer inspection. If the level continues to fall below all visible fittings, the issue may be lower in the shell, drain line or underground plumbing.
This approach has limits. Do not let the pool drain too far, especially in hot conditions or where ground pressure could affect the structure. A low water level can also damage pumps if the system is allowed to run dry. Switch off the circulation equipment if the water drops below the skimmer and seek professional advice rather than taking risks with the pool or its equipment.
Why dye testing can help, but only in the right place
Dye testing is useful when there is a suspected crack or gap in a visible area. A specialist introduces a small amount of coloured dye near the suspected point while the water is still. If there is a leak, the dye may be drawn towards it.
It can be particularly effective around lights, jets, steps, skimmers and fine cracks in accessible finishes. However, a dye test is not a complete answer for every pool. It will not locate a leak in a buried pipe, and water movement can make results unreliable. Using dye randomly across a large pool often wastes time and can lead to false conclusions.
A professional leak detection engineer uses dye as part of a structured investigation, not as a substitute for proper testing.
The best way to find pool leaks in hidden pipework
When the loss changes with the pump running, hidden circulation pipework becomes the main suspect. These pipes often run below the pool surround, garden or terrace, so digging based on a hunch can cause expensive and unnecessary damage.
The most reliable approach is non-invasive leak detection. First, the pipework is isolated and pressure tested to confirm whether it is holding water as it should. A pressure drop indicates a fault, while a stable test can rule out that section and focus attention elsewhere.
Depending on the pipe and pool layout, a specialist may then use acoustic detection to listen for the sound created by escaping water, or introduce a safe tracer gas into isolated pipework and detect where it reaches the surface. Compressed air testing may also be appropriate in certain systems. These methods allow the engineer to narrow down the leak location with far greater accuracy than visual inspection alone.
The right method depends on the construction of the pool, the type of pipework, ground conditions and whether the system can be safely isolated. That is why a one-size-fits-all repair quote before testing should be treated with caution.
Avoid common mistakes that make pool leaks worse
It is tempting to add more sealant, use a pour-in leak product or start lifting tiles as soon as the water level falls. These actions may occasionally provide a short-term improvement, but they can also hide the evidence needed to locate the real issue. Some sealants are unsuitable for pool finishes and can complicate later repairs.
Avoid repeatedly topping up the pool without investigating a persistent loss. Besides increasing your water costs, this can dilute pool chemicals and put more pressure on the filtration system. If leaking water is reaching soil beneath the terrace or nearby structures, it may contribute to movement, dampness and damage that is far more costly than an early detection visit.
Also be careful around electrical equipment. Water near pool lights, pumps or control systems should be treated seriously. Do not attempt repairs to electrical fittings yourself. Isolate power where it is safe to do so and arrange a qualified inspection.
When to call a pool leak detection specialist
A specialist is the sensible choice when the bucket test confirms a leak, the source is not obvious, water loss is significant, or pipework is likely involved. It is also worth calling early if you see saturated ground, unexplained damp on a nearby wall, cracking around the pool surround or a sudden increase in water use.
For homeowners in Costa Blanca North, Orihuela Costa, Torrevieja and nearby areas, Water Leak Services Spain provides a friendly, reliable service built around locating the source accurately before repairs begin. With non-invasive testing methods and a no find, no fee promise, the focus is on reducing disruption and giving you clear information about what needs to happen next.
Before the visit, make a note of how much water the pool has lost, whether the pump was running, when you first noticed the issue and any recent work carried out near the pool. These details can help speed up the investigation.
A precise location makes every repair simpler
The repair itself may be straightforward once the leak has been found: a failed seal, damaged fitting, cracked pipe or localised shell defect. The difficult part is reaching that answer without lifting a large area of terrace or replacing components that were never faulty.
Your pool should be a place to cool off and enjoy your home, not a source of uncertainty. If the water loss is more than evaporation, a prompt, accurate investigation gives you the best chance of stopping the problem while the repair remains small, controlled and affordable.